Swing Arm Cutting Presses

With over 60 years experience and thousands of sold machines, both in the footwear and in many other industries, make Atom the world leader among the producers of swing arm presses. The steady attention to customer feedback allowed Atom to manufacture a product able to fully satisfy the most compelling needs about reliability, productivity and energy savings.

Atom produces four main types of swing beam cutting presses, these include:

'Multiforce' (light swing)
This system automatically adjusts the cutting pressure required to increase ease of use, reducing the wear on the cutting board (up to 50%) and maximising energy economy.
SE Series (Entry Level)
A functional machine, constructed in the same way as other models, but even simpler to use. The basic machine, with automatic setting of stroke end, working with dies of different height is not a problem.
S100 Series
This type of cutting press is equipped with three different cutting pressures to enable the use of different sized (surface area) dies without any repeating adjustments.

All models are supplied with a CE Mark of conformity.

'Multiforce' Swing Beam Cutting Press

The 'Multiforce' differs from other swing beam cutting presses by operating to a stroke end system, therefore meaning it reaches the same depth each time. It also boasts the 'light swing' arm, which makes arm movement by the operator effortless.

The 'Multiforce' device allows a cutting board saving of up to 50%, so not only saving money, but also allowing better cutting across the board due to less wear, and so board reduced contours.

The 'light swing' arm can be supplied in a super light alloy, so yet again decreasing weight on the cutting beam, and so minimising operator effort required, and reducing fatigue.

All models are supplied with a CE Mark of conformity.

Multiforce Model	Cutting Table (mm)	Arm Width (mm)	Max. Cutting Power (ton/ kN)	Max. Stroke (mm)	Max. Daylight (No Board) (mm)	Motor Power (HP/ kW)	M/C Dimensions (mm)	Net. Weight (No Oil) (Kg)	Weight (Inc. Packaging) (Kg)
MF 20C	900x430	370	20t/ 196	90	125	1HP / 0.75kW	900x1000x1710	660	775
MF 9.1	900x450	370	22t/ 216				900x1090x1710	910	1030
MF 9.3S	900x450	370	25t/ 245				900x1090x1710	910	1030
MF 9.3	1000x500	370	25t/ 245				1000x1140x1710	1020	1150
MF 9.4	1000x500	500	25t/ 245				1000x1160x1710	1060	1190
MF 9.5	1000x500	610	25t/ 245				1000x1160x1710	1080	1210
MF 9.6	1200x500	610	22t/ 216				1200x1160x1710	1100	1230
MF 9.1A**	900x450	370	20t/ 196				900x1120x1710	910	1030
MF 9.4A**	1000x500	500	20t/ 196				1000x1130x1710	1060	1190

** (Super Light Alloy Arm) | S (Small) | C (Economy Version)

SE Series Swing Beam Cutting Press

This swing beam cutting press is extremely simple to use with easy adjustment of the cutting stroke, an operator can switch between multiple height cutting dies without any setting or adjustment.

The control push buttons are ergonomic, so allowing the operator increased comfort. The push buttons are controlled by a two hand safety relay, meaning the buttons need to be activated 5/10ths/sec between each other too allow cutting stroke activation, and requires constant activation to maintain a cut stroke.

The cutting power is easily adjusted if required through the movement of a simple potentiometer on the cutting beam.

The specifications and models available within this range are listed below:

All SE Series swing beam cutting presses are supplied with a CE Mark of conformity.

SE Series Model	Cutting Table (mm)	Arm Width (mm)	Max. Cutting Power (ton/ kN)	Max. Stroke (mm)	Max. Daylight (No Board) (mm)	Motor Power (HP/ kW)	M/C Dimensions (mm)	Net. Weight (No Oil) (Kg)	Weight (Inc. Packaging) (Kg)
SE 8	600x300	300	8t/ 78	90	125	1HP / 0.75kW	600x690x1330	430	500
SE 20C	900x430	370	20t/ 196				900x870x1400	630	745
SE 20	900x450	370	22t/ 216				900x960x1425	880	1000
SE 22	1200x500	500	22t/ 216				1200x1030x1425	1060	1200
SE 24C	900x450	370	25t/ 245				900x960x1425	880	1000
SE 24	1000x500	370	25t/ 245				1000x1010x1425	990	1120
SE 25C	900x450	500	25t/ 245				900x960x1425	900	1020
SE 25	1000x500	500	25t/ 245				1000x1030x1425	1030	1160
SE 25L	1000x500	610	25t/ 245				1000x1030x1425	1050	1180

L (Large) | C (Models Based On A New, Lighter Framework)

S100 Series Swing Beam Cutting Press

The S100 swing beam cutting press is like the SE Series simple to use with easy adjustment of the cutting stroke, an operator can switch between multiple height cutting dies without any setting or adjustment.

Unlike the SE swing beam the S100 has a 3 push button cutting power selection rack, this means that as an operator moves from a smaller die to a larger tool (surface area) rather then adjust the cutting power settings, any 1 of 3 buttons can be used on the left push button console to achieve an accurate cut.

The cutting power is easily adjusted if required through the movement of a two potentiometers on the cutting beam, the smaller of the two adjusts the 1st button of the 3 and the larger controls the 3rd push button. The 2nd push buttons cutting power is an average taken between the smaller and larger settings.